|
God drat it! All the stores around me are starting to have poo poo selection for tools. Lowes doesn't carry flare nut wrenches any more. The Craftsman set at Sears looks cheap but isn't priced that way. Are HF's flare nut wrenches good for things that mustn't be rounded?
|
# ? Dec 8, 2012 02:26 |
|
|
# ? Apr 23, 2024 09:49 |
|
Preoptopus posted:Is any one else's Matco guy a complete and utter dick for no good reason? Mine's not a dick but he has no clue how to sell one of his lovely tools.
|
# ? Dec 8, 2012 03:16 |
|
Jared592 posted:Ouch man c'mon There is more to Quality Control with soldering. Each job is different. It is easier to calibrate a crimper or a machine. A dumbass with a soldering iron cannot be calibrated. My company does neither: a story of how peacefrog spent last winter staring into a microscope. Your crimps look like gently caress at 40x. I can't even get your solderblobs into my depth of field. Wash that flux off!
|
# ? Dec 8, 2012 03:30 |
|
Lord Gaga posted:-ONLY USE UL LISTED TERMINALS. Autozone/Cheapest at Walmart/HF are not UL listed. I thought UL was pretty much bullshit.
|
# ? Dec 8, 2012 04:30 |
|
A properly done crimp with a good quality ratchet/hydro crimper is just as good as a perfectly done solder joint, and it's impossible to have solder accidentally wick up the strands of the wire and create a stress riser past the insulation/stress relief sleeve. That's why I use a decent ratchet crimper and sealant lined transparent heatshrink 3M terminals with fully brazed ferrules. Never had a failure. Crappy terminals and crappy crimpers can't compare. I think I bought my crimper for $25 or $30 at autozone, it doesn't have to be a massively expensive one, just make sure you do a few test crimps and pull-test them, then adjust the crimp firmness accordingly. e: also, UL can go to hell, look at the terminals and decide if they're quality yourself. And IIRC UL has nothing to do with rating automotive grade wire (unless it's cited in the respective SAE specs) - all the quality SXL-spec automotive primary wire I can find is rated to SAE J1128 with no direct mention of UL. kastein fucked around with this message at 04:38 on Dec 8, 2012 |
# ? Dec 8, 2012 04:34 |
|
Ive crimped RBY terminals that are stronger than the wire behind them. Do not look at the terminals and decide if theyre good for yourself, how would you make such a decision not stupidly? Anyway, in this case at least, no UL is not stupid. And with UL crimps and UL wire and a harbor freight ratcheting crimper you will get crimps that meet UL tensile test standards. If you dont use UL wire you wont. I know because I have tested wire from a variety of places with a wire tensile testing device.
|
# ? Dec 8, 2012 04:54 |
|
Phone posted:I thought UL was pretty much bullshit. It's a testing laboratory (Underwriters Laboratories) not a product or a standard, and it's not bullshit. Confused about crimping? Read this: http://www.molex.com/pdm_docs/ats/TM-640160065.pdf If you're lazy start at page 20 of 27. kastein posted:e: also, UL can go to hell, look at the terminals and decide if they're quality yourself. And IIRC UL has nothing to do with rating automotive grade wire (unless it's cited in the respective SAE specs) - all the quality SXL-spec automotive primary wire I can find is rated to SAE J1128 with no direct mention of UL. Also correct. The "new" standard is ISO 6722 however. That's a minimum of 0.465 millimeters core compared to the 0.508 millimeters of SAE J1128. Do not use crimp terminals between those standards. ISO wire minimum conductor size is controlled by the resistance of the wire core, so diameter might change depending on the core material used by the manufacturer. That's some more bullshit to account for when shopping crimp terminals. Lord Gaga posted:UL wire UL evaluates automotive wire against ISO 6722/DIN 72551 and/or SAE J1128. Lord Gaga posted:I am a senior in mechanical engineering Valid argument. I graduated 23 years ago Sir Cornelius fucked around with this message at 08:57 on Dec 8, 2012 |
# ? Dec 8, 2012 08:12 |
|
Phone posted:I thought UL was pretty much bullshit. Only if it's on bullshit grey-market merchandise. Ask me about how many devices I had catch fire during my two years in Latin America.. including fans, phones, and routers. From "reputable" Wal-Mart owned companies.
|
# ? Dec 8, 2012 17:21 |
|
SNiPER_Magnum posted:God drat it! All the stores around me are starting to have poo poo selection for tools. Lowes doesn't carry flare nut wrenches any more. The Craftsman set at Sears looks cheap but isn't priced that way. Are HF's flare nut wrenches good for things that mustn't be rounded? I got the craftsman set, wasn't thrilled with the $40 price tag, but they feel well made and did a great job with my clutch line fittings. They're nicely polished, and seem to fit well.
|
# ? Dec 9, 2012 00:53 |
|
My Cutmaster 42 arrived, DOA... I'm gonna swap it with Zoro, and hopefully have better luck with the next one.
|
# ? Dec 9, 2012 00:58 |
|
sharkytm posted:My Cutmaster 42 arrived, DOA... I'm gonna swap it with Zoro, and hopefully have better luck with the next one. yay dyslexic brain. Read it as a cumtaster. Anyway what is a cutmaster?
|
# ? Dec 9, 2012 01:55 |
|
General_Failure posted:yay dyslexic brain. Read it as a cumtaster. Anyway what is a cutmaster? Obviously it's a tool for circumcisions.
|
# ? Dec 9, 2012 03:06 |
|
MiniFoo posted:Obviously it's a tool for circumcisions. The best part of being a mohel is - the tips are free!
|
# ? Dec 9, 2012 03:12 |
|
General_Failure posted:yay dyslexic brain. Read it as a cumtaster. Anyway what is a cutmaster? Thermal dynamics plasma cutter.
|
# ? Dec 9, 2012 03:15 |
|
mod sassinator posted:So this 12v portable (but not cordless) 1/2 inch impact wrench is only 40 bucks today: http://www.amazon.com/gp/product/B00544EZQ2/?tag=dealnewscom&m=ATVPDKIKX0DER Got a chance to use the impact wrench today and I'm pretty happy with it. I can pull a tire off in about 30-60 seconds now, and do it while it's in the air instead of breaking the torque on the ground, lifting, and then removing. Rotating tires is a snap with this tool.
|
# ? Dec 9, 2012 03:33 |
|
This isn't really a tool, more something to carry your tools in. http://www.homedepot.com/h_d1/N-5yc1v/R-202018009/h_d2/ProductDisplay?catalogId=10053&langId=-1&keyword=tool+bag&storeId=10051#.UMP_43e8rY0 I've got basically my entire tool collection in it - something like 80+ pounds of tools, everything needed to work on my vehicles aside from a few things like the GM steering column toolkit, balljoint press, etc. It lasted 6-8 months of being dragged around junkyards, slid across gravel, and otherwise being abused before the outer pockets started to come unstitched and the bottoms started to blow out. At the price, it's 100% worth it, I may just keep buying a new one every 6 months without a single complaint, I'm not exactly nice to it. I've managed to pack all of this into it... * full set of spark plug sockets * full set of 1/2" extension bars * full set of 3/8" extension bars * full set of 1/4" extension bars * 1/2, 3/8, and 2x 1/4 ratchets * two 1/2 breaker bars * full set of deep SAE impact sockets * full set of shallow metric impact sockets * full set 12pt metric sockets * full set 12pt SAE sockets * full set Torx drivers * full set e-Torx sockets * full set SAE allen bits * full set metric allen bits * half a dozen screwdrivers * full set SAE gearwrenches * full set metric gearwrenches * 1 1/16, 2x 7/8, 15/16, and 21mm box wrenches * 1 1/4 deep impact socket * 5/16 deep and shallow 6pt sockets (1/4 drive) * 4lb blacksmiths hammer * large Wiss tin snips * long-reach dikes * linemans pliers * two packs of long sawzall blades * one pack of 4.5" cutoff wheels * drift punch, centerpunch, two cold chisels * large mechanics prybar * 5/16 and 8mm 6pt box wrenches * steering wheel / harmonic balancer puller toolset * tamperproof screwdriver bit set and screwdriver handle * full set u-joints, drive adapters, etc * serpentine belt tensioner toolset * large gear puller * air impact driver * seal puller * 8mm and 10mm nutdrivers * a handful of metal files * full set deep 1/4 drive 12pt SAE sockets * full set deep 3/8 drive 12pt SAE sockets * snapring pliers, circlip pliers I can basically grab my angle grinder and sawzall, their battery packs, the high-lift jack, and hit the junkyard without a single thought about what tools I'll need, because they're all there. Or for that matter, get a call from a stranded friend at midnight, sling the toolbag in the truck, and fix whatever they're driving on the side of the road.
|
# ? Dec 9, 2012 04:23 |
|
I'm looking to buy a creeper for my boyfriend for Christmas. He's 6'4" and 230 lbs so something that's fairly heavy duty would be good. I've just done some cursory googling and I'm sort of at a loss! I don't really know the pros and cons of any of them (plastic? Steel? 4 wheel? 6? Convertible? Not?). So...any advice? He works almost exclusively on older Toyota trucks and SUVs, if that makes a difference (more clearance?).
|
# ? Dec 9, 2012 20:28 |
|
soap. posted:He works almost exclusively on older Toyota trucks and SUVs, if that makes a difference (more clearance?). Cardboard boxes are cheap as hell..
|
# ? Dec 9, 2012 20:55 |
|
soap. posted:I'm looking to buy a creeper for my boyfriend for Christmas. If it's a tool you're talking about, you're pretty much the best girlfriend ever. What you're looking for is probably a crimping tool. A creeper is something like forum poster "Viggen". I don't know where you live or what the budget is, but if you want to go cheap, this is a rather good tool: http://www.harborfreight.com/ratcheting-crimping-tool-97420.html If you love him enough to break the bank, Wiha is where it is. http://www.wihatools.com/400seri/436_crimps.htm
|
# ? Dec 9, 2012 21:16 |
|
Sir Cornelius posted:If it's a tool you're talking about, you're pretty much the best girlfriend ever. What you want is actually this. Sir Cornelius posted:What you're looking for is probably a crimping tool. A creeper is something like forum poster "Viggen".
|
# ? Dec 9, 2012 21:22 |
|
Viggen posted:What you want is actually this. hehe, yeah, that makes sense. gently caress, now I want a creeper.
|
# ? Dec 9, 2012 21:24 |
|
Does he normally work on a smooth floor / surface? Small wheels can be a pain to push around on uneven surfaces.
|
# ? Dec 9, 2012 21:26 |
|
Do you guys know where I can get exhaust clamps for dirt cheap? I paid $11 for a temporary flex pipe + 1 clamp and it seems silly to pay more than half that for just a single clamp.
|
# ? Dec 9, 2012 21:47 |
|
Drunk Pledge Driver posted:Do you guys know where I can get exhaust clamps for dirt cheap? I paid $11 for a temporary flex pipe + 1 clamp and it seems silly to pay more than half that for just a single clamp. ..wire hanger? But really, that isn't too out-of-sorts. Check with your local automotive store.
|
# ? Dec 9, 2012 21:48 |
|
Colonel K posted:Does he normally work on a smooth floor / surface? Small wheels can be a pain to push around on uneven surfaces. Thanks a lot for this. You actually got me thinking. Small wheels aren't necessarily a problem if they're wide enough and have good bearings. Hmm, I've got at least 4 skateboard trucks and some good wheels, bearing and plywood in my workshop. I've never used a creeper. I've been so privileged to have lifts available most of the times I've needed to seriously work beneath a car. If not, I've just used a camping sleeping mattress like this http://www.worldofcamping.co.uk/sunncamp-self-inflating-mattress-1337 Hmm, I feel a creeper project is boiling.
|
# ? Dec 9, 2012 21:49 |
|
Sir Cornelius posted:hehe, yeah, that makes sense. gently caress, now I want a creeper. grover fucked around with this message at 21:52 on Dec 9, 2012 |
# ? Dec 9, 2012 21:50 |
|
Sir Cornelius posted:Thanks a lot for this. You actually got me thinking. Small wheels aren't necessarily a problem if they're wide enough and have good bearings. Hmm, I've got at least 4 skateboard trucks and some good wheels, bearing and plywood in my workshop. Make sure the wheels are MOBILE. The smaller they are and the more they can pivot - the better off you will be. The most broken creepers are the best that I've used, because you don't have to fight (and sometimes bang your knees), I use a big oil stained cardboard box.
|
# ? Dec 9, 2012 21:51 |
|
The bigger the wheels are and the stronger their swivels are, the better. Also, as a 6'4" dude working on SUVs and trucks, he definitely wants 6 wheels. Plastic ones are usually a little flexy but metal ones tend to break if you don't clean the floor well and the wheels jam into things occasionally. Clearance shouldn't matter much with SUVs and trucks but the lower it is in the middle the better. I use my craigslist special used motorcycle jacket in the summer and a sheet of cardboard in the winter since it slides very nicely on packed snow or ice... or an actual creeper when I'm over at a friends shop. The cement floor and creeper is way better.
|
# ? Dec 9, 2012 22:19 |
|
kastein posted:The bigger the wheels are and the stronger their swivels are, the better. Also, you definitely want 6. Wait until they get dirt in them. In the winter. They're not very mobile. I like the smaller wheels for a reason.
|
# ? Dec 9, 2012 22:19 |
|
yeah that's no fun There are a few flat wheels on the ones at ACEofsnett's shop - mostly from exactly that. But the bigger wheels with stronger swivels will power over dirt, while smaller weaker wheels will flex sideways and wear flat spots into the wheel instead.
|
# ? Dec 9, 2012 22:21 |
|
If anything look for a creeper with a headrest that tilts up. When I am working on the range rover its nice to have your head tilted up just ever so much. Just a couple of inches means the difference of a strained neck in the morning.
|
# ? Dec 9, 2012 22:24 |
|
soap. posted:I'm looking to buy a creeper for my boyfriend for Christmas. He's 6'4" and 230 lbs so something that's fairly heavy duty would be good. I've just done some cursory googling and I'm sort of at a loss! I don't really know the pros and cons of any of them (plastic? Steel? 4 wheel? 6? If he mainly works on trucks/SUVs, that does help, as it means he doesn't need the lowest possible height I'll also second what people have said about small wheels being horrible on anything other than a perfectly smooth surface. I'd definitely go for the largest wheels available. Tool trays can be handy, provided they're at the right "grabbing" level when you're lying on the creeper, but not essential. There is "The Bone" creeper, which seems to have a good reputation, though I've never used one myself, and they are noticeably more expensive than other options. I'm not sure they're worth the money. I use this one, as and when I need to, and it does ok on my brick/paving driveway (with a certain amount of gravel getting onto it). It does get hung up on small stones etc, but not badly enough for me to worry too much. It's "ok" but not brilliant. I'd prefer it to be a fraction longer than its 40" overall length, too. In other news, I decided to get my old man one of these for Christmas: http://www.sealey.co.uk/PLPageBuilder.asp?id=20&method=mViewProduct&productid=15678 He doesn't need one, as he does have a torque wrench already, but I'm hoping the Cool New Toy factor will encourage him to do some stuff with his cars.
|
# ? Dec 9, 2012 23:36 |
|
SNiPER_Magnum posted:God drat it! All the stores around me are starting to have poo poo selection for tools. Lowes doesn't carry flare nut wrenches any more. The Craftsman set at Sears looks cheap but isn't priced that way. Are HF's flare nut wrenches good for things that mustn't be rounded? Mine were poo poo and rounded off everything they touched and by everything I mean after the 2nd fitting I threw them into the woods while yelling expletives
|
# ? Dec 9, 2012 23:45 |
|
Thanks for all the advice everyone. So far something like http://www.amazon.com/gp/aw/cr/B000M5WV7I/ref=aw_d_crstars_automotive?qid=1355120463&sr=1-16 looks good. Unless someone has experience with the Bone creeper. I'm willing to shell out for it if its really worth it. He has a shop so there's no rough terrain issue. Anything else I should consider? Any other opinions on steel vs. plastic? EDIT: I'm also going to ask for general advice here. If you guys could receive any tool as a gift before you were going to do an engine swap, what would you want? We just totalled his truck in a freak accident (someone abandoned their car with no lights and no reflectors in the fast land of a dark stretch of freeway; we clipped it at 65mph and rolled.) The engine survived, though, and we're getting a new 4runner carcass to swap it in to. He had just swapped this engine in, too. So he has everything he strictly needs, but can you think of anything I could give him tool-wise that would make it easier? I just thought a creeper would make it easier on his back (and his clothes, although I'm kind of fond of the smell of gear oil). But I'm open to suggestions! soap. fucked around with this message at 07:42 on Dec 10, 2012 |
# ? Dec 10, 2012 07:31 |
|
Yeah, the HF flare wrenches are poo poo. The ends are really fat (for extra strength?) and won't fit anywhere remotely tight. You know, where you'd need them.
|
# ? Dec 10, 2012 07:31 |
|
Does anyone have some recommendations on a nice set of 3/8ths inch drive metric allen keys? Mine are starting to poo poo the bed and as a result I'm stripping way more allen bolts which leads to rage and yelling.
|
# ? Dec 10, 2012 07:37 |
|
Doctor Londom posted:Yeah, the HF flare wrenches are poo poo. The ends are really fat (for extra strength?) and won't fit anywhere remotely tight. You know, where you'd need them. Oh good its not just me, I recently purchased a set and was pretty disappointed despite the low price.
|
# ? Dec 10, 2012 08:01 |
|
The HF flare nut wrenches worked fine for me, but then again I live in the desert.
|
# ? Dec 10, 2012 08:30 |
|
soap. posted:I just thought a creeper would make it easier on his back (and his clothes, although I'm kind of fond of the smell of gear oil). But I'm open to suggestions! Your obviously a good g/f. I would just get him a nice gift card to where ever he seems to shop the most for tools. As of right now, I am pretty set on tools, but I do have a $50 sears gift card sitting in the tool chest waiting to be used (yes, I keep it in the chest along with other random assorted things, don't ask). Or a gift certificate to NAPA is always handy. You know, buying fluids, random poo poo, etc. But yet again I am told that I am about impossible to shop for, so take that for what its worth.
|
# ? Dec 10, 2012 11:00 |
|
|
# ? Apr 23, 2024 09:49 |
|
Z3n posted:Does anyone have some recommendations on a nice set of 3/8ths inch drive metric allen keys? Mine are starting to poo poo the bed and as a result I'm stripping way more allen bolts which leads to rage and yelling.
|
# ? Dec 10, 2012 13:22 |