|
Gotta say, that air filter about 3/4 the way through was a mechanical success. It kept all of that out of the engine, theoretically. Some of that other stuff, woo...
|
# ? Jan 23, 2020 00:08 |
|
|
# ? Apr 18, 2024 13:43 |
|
https://i.imgur.com/v8aK9kR.mp4
|
# ? Jan 23, 2020 02:32 |
|
What I really want to know is what the "whale" switch at 8:06 is for.
|
# ? Jan 23, 2020 02:37 |
|
Oh there’s what IOC’s av is up to these days!
|
# ? Jan 23, 2020 19:04 |
|
I can't stop laughing at this. Who knew domestic trucks had mastered physical comedy?
|
# ? Jan 23, 2020 22:22 |
|
Didn't he kill Tasha Yar?
|
# ? Jan 24, 2020 01:55 |
|
Mister Kingdom posted:Didn't he kill Tasha Yar?
|
# ? Jan 24, 2020 18:38 |
|
Fifty Three posted:No, that was Yasha Tar. drat
|
# ? Jan 24, 2020 20:07 |
|
Kinda fits with the thread, too.
|
# ? Jan 25, 2020 07:17 |
|
I heard a loud bang on corner exit yesterday followed by card in bicycle spoke noise. That doesn't look good. Typical AP1 S2000 rear diff bearing cap failure It lived 25 minutes of track time and about 100mi of street driving (I bought it used).
|
# ? Jan 26, 2020 19:25 |
|
Are they known to do that, then? Hopefully your diff centre itself is unharmed and you can transpose it into another casing with a new CWP set. Is there a reinforcement option available?
|
# ? Jan 26, 2020 19:35 |
|
Yeah, it is known but not really that common in stock power cars. The AP2 diff was changed to prevent this and there are companies that sell reinforcement kits for the stock diffs, this one was built but you can only do so much with the AP1. I'm going to put my original OEM torsen diff back in the car for now while I look for a used AP2 diff to build. Just pulled the ring gear out BlackMK4 fucked around with this message at 19:45 on Jan 26, 2020 |
# ? Jan 26, 2020 19:43 |
|
That’s some tasty chewed up metal.
|
# ? Jan 27, 2020 01:39 |
|
That right there is some quality home-grown content for this thread, drat.
|
# ? Jan 27, 2020 02:44 |
|
Elviscat posted:That right there is some quality home-ground content for this thread, drat.
|
# ? Jan 27, 2020 02:50 |
|
Now with video https://www.youtube.com/watch?v=g25efzfuS2I I thought I tore the exhaust off at first because it sounded like that with no vibration or change in power delivery
|
# ? Jan 27, 2020 05:10 |
|
I blew up the diff in my old 535i like that drifting in a parking lot in the rain. Big bang but felt okay otherwise, drove home with no incident. Trying to drive the car the next day when it wasn’t raining it behaved a bit differently, she really didn’t like turning any more, with the 265 tires on the back the inside one put up a hell of a fight.
|
# ? Jan 27, 2020 05:21 |
|
BlackMK4 posted:Now with video Did the Integra driver wave back when you pulled off the track? That sucks though, pretty surprised it still moved with that much carnage.
|
# ? Jan 27, 2020 05:54 |
|
BlackMK4 posted:Now with video excellent driving
|
# ? Jan 27, 2020 21:01 |
|
STR posted:Did the Integra driver wave back when you pulled off the track? That surprised me, too.
|
# ? Jan 27, 2020 21:22 |
|
BraveUlysses posted:excellent driving thank you, sir STR posted:Did the Integra driver wave back when you pulled off the track? We're friends, he broke his poo poo the next day
|
# ? Jan 28, 2020 04:03 |
|
So fun one today. We ordered a fastener installation tool. It's a two-part tool, each part costs $250. Part A is an anvil, part B is a punch/set tool. The fastener sits between part A and part B. The punch has a hole in it to fit the fastener. When I opened the package to use the tool, I discovered that the punch wouldn't fit around the fastener. I checked the part specification diagram, and the hole in the center is marked " .219" diameter, reamed." This one measured .197", and showed no interior tool marks. For $250, they couldn't even manage to finish making the thing before they mailed it to us. .197" turns out to be 5mm on the nose; I have a sneaking suspicion these things are made overseas and just don't get the QA that an aircraft repair tool deserves. Our parts guy yelled at the supplier, and we'll have a new one in the morning.
|
# ? Jan 31, 2020 02:30 |
|
No, that sounds about right. I suspect what happened is they've either mistakenly shipped you a 5mm one - but then I would expect it'd be marked with something - or they're all initially drilled at 5mm then taken out to the final size and this one skipped a step. If it's a proprietary design to a given company, tell them about it, it could even be a knock-off that's got into the supply chain, and people in aerospace do not take kindly to that.
|
# ? Jan 31, 2020 16:16 |
|
InitialDave posted:it could even be a knock-off that's got into the supply chain, and people in aerospace do not take kindly to that. Seriously this. There are chinese knockoffs of most aerospace tools and getting in to the supply chain is a big deal. Even something rather specific like: $700 Chinese Four Indent Military Crimp Tool from Alibaba $1400 American Four Indent Military Crimp Tool https://www.dmctools.com/oscar/catalogue/wa27f_3698/ CarForumPoster fucked around with this message at 18:44 on Jan 31, 2020 |
# ? Jan 31, 2020 18:39 |
|
Doesn't really matter, because some grunt is just going to use some random tool he keeps in his pocket. Reminds me of when I was setting up a DoD facility and we kept testing the cat6 cables back to the comm room and they were all failing. We go into the comm room and the cable dogs are in there terminating the cables into patch panels. Instead of using an actual tool for the job, or hell, a pair of flush cutters, one guy was using what looked like a prison shiv to cut the individual wires after pressing them into the little metal blocks that went into the patch panel. He couldn't cut them short enough, so the wires pushed up against the metal casing and shorted out.
|
# ? Jan 31, 2020 18:48 |
|
CarForumPoster posted:Seriously this. There are chinese knockoffs of most aerospace tools and getting in to the supply chain is a big deal. This doesn't surprise me. What really surprises me is that this tool doesn't a have a super value coupon in the Harbor Freight flyer.
|
# ? Jan 31, 2020 18:57 |
|
Colostomy Bag posted:This doesn't surprise me. I'd bet theres more harbor freight store locations than companies using pnuematic 4 indent military crimpers.
|
# ? Jan 31, 2020 18:58 |
|
Cojawfee posted:Doesn't really matter, because some grunt is just going to use some random tool he keeps in his pocket. Reminds me of when I was setting up a DoD facility and we kept testing the cat6 cables back to the comm room and they were all failing. We go into the comm room and the cable dogs are in there terminating the cables into patch panels. Instead of using an actual tool for the job, or hell, a pair of flush cutters, one guy was using what looked like a prison shiv to cut the individual wires after pressing them into the little metal blocks that went into the patch panel. He couldn't cut them short enough, so the wires pushed up against the metal casing and shorted out. Ahhhh they must have upgraded from Gerber's and tanto blade flip knifes.
|
# ? Jan 31, 2020 23:13 |
|
If it was the Navy it'd be a digit (multitool/leatherman)
|
# ? Feb 1, 2020 03:20 |
|
InitialDave posted:No, that sounds about right. They were very apologetic. The customer service rep said "your technician is VERY detail-oriented." Yeah, I documented the exact discrepancy on an aviation part, just like I do literally every day for every task. At the risk of throwing them under the bus, it was a Dzus installation tool. Notice it's got a product spec sheet with callouts for every dimension? There's no other thing this thing could be for. I don't see another product in their line like this, and the one we got has the part number roll-stamped into the tool. $250 for that thing, btw, after shipping and everything. The new one showed up today with an ID of .214". It was reamed, but whatever galvy process went on after was kinda lumpy and garbage. I'm sure it'll peel off eventually, but the QC on these is straight trash, and I think they're getting $20 parts from China or somewhere else metric with low QC and marking them up 1000%. Another mechanical failure; this time with crimpers. The shop owns a Daniels Wire Repair Kit for one of our airframes. In it is all the high-quality Daniels crimpers with turrets, Ideal strippers, pin pushers, pullers, extractors, gauges. I was using the M22520/2-01 (an Astro Tool version, not the Daniels) and went to set the crimp stop to the correct wire gauge when I hear some little springy thing go whizzing past my ear and pieces fall into the nose avionics bay. Astro is sending us a loaner for Monday and we're sending this one to them to be overhauled. $100 for this service, and well worth it. Because I couldn't just stop crimping pins, I sacrificed a ballpoint pen to the cause and managed to get the thing operational for one wire gauge. It'll make legal crimps for 22awg now, but doesn't validate the "go/no-go" gauge for anything else.
|
# ? Feb 1, 2020 03:53 |
|
Cojawfee posted:Doesn't really matter, because some grunt is just going to use some random tool he keeps in his pocket. Reminds me of when I was setting up a DoD facility and we kept testing the cat6 cables back to the comm room and they were all failing. We go into the comm room and the cable dogs are in there terminating the cables into patch panels. Instead of using an actual tool for the job, or hell, a pair of flush cutters, one guy was using what looked like a prison shiv to cut the individual wires after pressing them into the little metal blocks that went into the patch panel. He couldn't cut them short enough, so the wires pushed up against the metal casing and shorted out. Sounds like needing to re-wire a PBX without the right tools, and blasting a chip out of my Leatherman pocket knife because it was the only option I had for forcing the cables onto the pins inside the phone closet. I'll see if I can find the knife so I can take a photo. I buffed most of the chip out, but there's still a crescent moon of scorched steel where it shorted.
|
# ? Feb 1, 2020 06:09 |
|
babyeatingpsychopath posted:It was reamed, but whatever galvy process went on after was kinda lumpy and garbage. I'm sure it'll peel off eventually, but the QC on these is straight trash, and I think they're getting $20 parts from China or somewhere else metric with low QC and marking them up 1000%. If it's anything like what I have to deal with, the company that sells it can't make money producing it so they pawn it off to a third party for cheaper production and didn't flow down all requirements and their receiving inspection team either didn't know or didn't care. Possibly a first/last check instead of sample plan or 100% doc. Why yes, I'm in QA/QC for an aero/O&G manufacturer, why do you ask?
|
# ? Feb 1, 2020 12:30 |
|
babyeatingpsychopath posted:They were very apologetic. The customer service rep said "your technician is VERY detail-oriented." Yeah, I documented the exact discrepancy on an aviation part, just like I do literally every day for every task. At the risk of throwing them under the bus, it was a Dzus installation tool. Notice it's got a product spec sheet with callouts for every dimension? There's no other thing this thing could be for. I don't see another product in their line like this, and the one we got has the part number roll-stamped into the tool. $250 for that thing, btw, after shipping and everything. The new one showed up today with an ID of .214". It was reamed, but whatever galvy process went on after was kinda lumpy and garbage. I'm sure it'll peel off eventually, but the QC on these is straight trash, and I think they're getting $20 parts from China or somewhere else metric with low QC and marking them up 1000%. Is this post going to be an eventual Exhibit A?
|
# ? Feb 1, 2020 13:59 |
|
I test newly installed or modified cables onboard USN ships all the time and the variety in quality of work is pretty LOL. I tested a new elliptical wave guide and was getting ridiculous VSWR measurements back, turns out the installers accidentally filled the waveguide with water while testing the dry air lines. Complete tearout and replacement. I've seen things you people wouldn't believe. LDF4-50 cables bent at right angles in the overheads. 96 pin cannon plugs completely wired in reverse. All those moments will be lost in time, like tears in the rain. Time to die.
|
# ? Feb 1, 2020 16:27 |
|
My mate got the coilovers off his Stagea.
|
# ? Feb 1, 2020 20:41 |
|
Well, I mean the coils are still coiled....
|
# ? Feb 1, 2020 20:46 |
|
Oh the dampers are hosed too, don't you worry.
|
# ? Feb 1, 2020 20:58 |
|
Colostomy Bag posted:When I got clipped...they were digging around and found a spot where I wasn't numb. You can imagine that joy. So yeah a horrible failure. Lol, same. I nearly hit the bloody ceiling. Still drove myself home, made it all the way to my house then scraped the car on the gatepost
|
# ? Feb 1, 2020 21:02 |
|
insta posted:Is this post going to be an eventual Exhibit A? If it passes the "go/no-go" it's a valid crimp. That's what the gauges are for.
|
# ? Feb 1, 2020 21:43 |
|
|
# ? Apr 18, 2024 13:43 |
|
https://twitter.com/morocco21/status/1223646348399955968?s=20 turn on audio https://i.imgur.com/KR88MDy.mp4
|
# ? Feb 2, 2020 08:40 |