|
A gift arrived! I received a fantastic set of matching coasters in the mail today, which immediately became the nicest coasters in my house: Action shot showing an admirable level of coastering in the defense of my sideboard: Finally, a bonus shot of Lamia attempting to eat the box in which they were delivered, because she is not bright: Thank you, oXDemosthenesXo!
|
# ? Dec 12, 2020 01:10 |
|
|
# ? Apr 25, 2024 23:18 |
|
Shame Boy posted:My wife was the one who picked it up from the mail and was like "Uhh... I assume this is for you right... it's got The Hacker Forum Word on it" Glad you enjoyed! I certainly had fun putting it all together. It sort of started with the white and gold knoblike button and went from there. The sine wave is made with retroreflective thread, so if the light hits it from the right angle, it lights up (phone flashlight works very well for this). The radio bits all came out of a decaying cabinet radio that I hauled off the curb and scavenged for parts. I did some research and I think it was originally from 1927? Anyway, I have the rest of the guts in my basement if you're interested and want to pay $$$ for shipping since it's stupidly heavy.
|
# ? Dec 12, 2020 03:24 |
|
mjan posted:A gift arrived! Brother: hey I got these thin endgrain offcuts Me: huh? Brother: contractors effed up Me: Lol sure I'll take them. wonder what to do with them DIY Discord: Coasters! Laser some poo poo on top! Me: Hey I have all that stuff! Prepping LASER BEAMS All etched, a couple of practice pieces on the left After finishing and corking the bottoms Glad you like them. I had no idea what I was going to make you until these precut pieces and bunch of good ideas from y'all showed up. I reused the box that TooMuchAbstraction sent my gift, so Lamia has good taste.
|
# ? Dec 12, 2020 06:06 |
|
is that suppose to be an end grain butcherblock floor?....is that a thing?
|
# ? Dec 12, 2020 07:24 |
|
JEEVES420 posted:is that suppose to be an end grain butcherblock floor?....is that a thing? i like it. wonder if scratches will “heal” themselves over time.
|
# ? Dec 12, 2020 15:17 |
|
JEEVES420 posted:is that suppose to be an end grain butcherblock floor?....is that a thing? It's a thing. Apparently it was used a lot in industrial buildings because they're easy on the feet.
|
# ? Dec 12, 2020 16:22 |
|
there wolf posted:
that's awesome.
|
# ? Dec 12, 2020 16:31 |
|
there wolf posted:
Used to be used for street paving too, but I think the right way to do it is with 3" long chunks that are laid in grout/mortar, not glue tiny slices to plywood and to make your own 'engineered' flooring and hope they don't move around too much. Makes some neat coasters though!
|
# ? Dec 12, 2020 16:42 |
|
Kaiser Schnitzel posted:Used to be used for street paving too, but I think the right way to do it is with 3" long chunks that are laid in grout/mortar, not glue tiny slices to plywood and to make your own 'engineered' flooring and hope they don't move around too much. you're probably right but most residential flooring is never going to be subjected to the kind of use that a street or factory floor would
|
# ? Dec 12, 2020 17:06 |
|
Yeah it was supposed to be flooring at some project my brother was managing. Obviously they didn't do it quite right. There's a museum in town that has one huge room that's about 100ft x 100ft of true dimension 2x4 end grain flooring and it's totally awesome.
|
# ? Dec 12, 2020 18:41 |
|
It's on my list of things I will do if I ever build a house instead of buying one. I'm already set on <1000sqft so expensive, longlasting features like that are going everywhere.
|
# ? Dec 12, 2020 19:42 |
|
This thread is fun because whenever a santee posts we get a behind the scenes making-of post from the santa
|
# ? Dec 13, 2020 02:21 |
|
Two steps forward, one step back on my santee's main gift. Recoverable, but each unforced error means I have to make it a tiny bit smaller, since I've got no do-overs on the material.
|
# ? Dec 13, 2020 17:04 |
|
Jaded Burnout posted:Two steps forward, one step back on my santee's main gift. Recoverable, but each unforced error means I have to make it a tiny bit smaller, since I've got no do-overs on the material. It'll sure save you on shipping though!
|
# ? Dec 13, 2020 17:16 |
|
Kaiser Schnitzel posted:It'll sure save you on shipping though! End up posting it in a kinder egg pod.
|
# ? Dec 13, 2020 17:17 |
|
The first part of my Concealed Cernnunos has arrived! My army grows stronger. Legit, excited about the protractor on the long one. Usually you only get 45oand 60o and I want more variety in my triangles! Thank you, Jaded and I'm looking forward to the other half in the new year, kinder egg or not.
|
# ? Dec 14, 2020 03:38 |
|
|
# ? Dec 14, 2020 10:19 |
|
Whatever could this be?! I wonder why it suddenly got colder the day this arrived....it must have brought some chill with it. Did it ever bring some chill! It's the BYOB hammock kitty, incredibly beautifully rendered in embroidery! Thank you Bingo Bango. How Wonderful! of a gift!
|
# ? Dec 15, 2020 00:58 |
|
i got a package today too! i assume it’s from this thread, because i can’t imagine it coming from elsewhere. model planes and a paint set! thanks mysterious australian friend (i assume you don’t want your real name broadcast lol)!! these are cool and i’ve never done anything like this so if anyone has tips, i’m open. should be a good january activity.
|
# ? Dec 15, 2020 01:09 |
|
Kaiser Schnitzel posted:Whatever could this be?! Oh, that's lovely!
|
# ? Dec 15, 2020 01:43 |
|
Kaiser Schnitzel posted:Whatever could this be?! I'm so happy USPS didn't mangle it! I hope it fills your days (and nights) with chill vibes.
|
# ? Dec 15, 2020 02:12 |
|
I came across that hammock kitty somewhere else recently... I think it might be one of the gifs in Microsoft Teams chat?
|
# ? Dec 15, 2020 02:28 |
|
mediaphage posted:i got a package today too! i assume it’s from this thread, because i can’t imagine it coming from elsewhere. No worries mate! We have a Scale modeling thread here, and Scalemates is the encyclopedia. Also here's some painting inspiration for the Albatros (and why I picked it) The only parts that aren't original are the repairs to the undercarriage made by the Royal Flying Corps in 1918 (it made a rough landing rather than crashed, the pilot survived). The collection at AWM is truly astonishing. There's another package coming... at some point. NTRabbit fucked around with this message at 03:57 on Dec 15, 2020 |
# ? Dec 15, 2020 03:39 |
|
I have recieved the best kind of mail, squishy mail! (Once removed from the box that is.) Beauty shot of the yarn hand dyed by my Santa! Bonus box shots: Thank you so much Hungry Medusa! The roving is SO soft and I love the colorway of the merino you dyed :3 It’ll be perfect for an amigurumi I have planned! The spindles are so beautiful too! I can’t wait to learn how to use them. Thank you again!!!
|
# ? Dec 18, 2020 06:04 |
|
I got a package! And it's so absolutely lovely, thank you peanut!!! Apart from now beeing some kind of millionaire apparently, I got an absolutely awesome christmas tree ornament, and a new years door decoration. I googled a bit, is it a Shimekazari (welcomes gods of good fortune, drives out all the bad stuff)? But there also is a huge stack of origami paper (the picture doesn't show how beautiful glittery-gold they are). I'll try myself on my first crane next week at christmas and will post the results here (if my fingers aren't tied into a knot). Also a lovely handwritten card! Thank you, peanut! Well setup our christmas tree this sunday, and the ornament will get a special spot!
|
# ? Dec 18, 2020 14:13 |
|
Hey everyone! Just to prevent future confusion if you send out a thank you card or gift to your santa that's fine but please make it clear that it's a thank you and not the main gift! Both me and tuo's santa just had a bit of a panic making sure wires weren't crossed.
|
# ? Dec 18, 2020 18:12 |
|
Huh? Did I do something wrong? I'm confused... (did I doxx my santee? I can't read kanji....) e: I'm currently working through some crane folding instructions and I fear my fingers fall off... tuo fucked around with this message at 18:33 on Dec 18, 2020 |
# ? Dec 18, 2020 18:30 |
|
tuo posted:Huh? Did I do something wrong? I'm confused... You’re fine! I just got a message from your Santa whose gift hasn’t arrived yet wondering if you got assigned two Santas somehow!
|
# ? Dec 18, 2020 19:30 |
|
Oh my god, now I kinda feel like an idiot :/
|
# ? Dec 18, 2020 19:44 |
|
corgski posted:You’re fine! I just got a message from your Santa whose gift hasn’t arrived yet wondering if you got assigned two Santas somehow! peanut is absolutely unstoppable, if she gets her hands on your address you're getting STUFF FROM JAPAN, what a menace!
|
# ? Dec 18, 2020 23:02 |
|
Truly shameful abdication of duty to not have posted this yet. This phenomenal gift from Mjan inspired me to put a lot more effort into my gift (which may now arrive after Christmas, sorry). Anyhow, take a look at this hand forged Drawknife that Mjan made! It is currently living on the tool rack above my bench, and I'm looking forward to my next chair project so I can put it to use! Thank you so much Mjan!
|
# ? Dec 18, 2020 23:08 |
|
GEMorris posted:Anyhow, take a look at this hand forged Drawknife that Mjan made! It is currently living on the tool rack above my bench, and I'm looking forward to my next chair project so I can put it to use! That is amazing
|
# ? Dec 18, 2020 23:10 |
|
Holy cow, that's a gorgeous tool.
|
# ? Dec 19, 2020 00:44 |
|
tuo posted:I got a package! And it's so absolutely lovely, thank you peanut!!! Yes, this is a thank you gift!!! Sorry for the confusion. Please send Tuo hella gifts. My Santee will also be getting a similar 2nd package because the DIY stuff wasn't ready for the 1st.
|
# ? Dec 19, 2020 00:58 |
|
Glad it arrived safe and sound, I had a ton of fun putting it together! Abbreviated build log follows: 1. Starting out with ~14" of 1084: 2. Forging the first arm. Should I ever do this again, I'd build a jig instead of freehanding it: 3. Both arms forged out, some rough profiling, and makers mark: 4. Adding the clay (technically, furnace cement) to the areas that I don't want hardened. For folks unfamiliar with this, you harden this particular type of tool steel by heating it up to what's known as the "critical temperature" (~1350F) and then rapidly cooling it. If it cools quickly enough, it solidifies in a hard, brittle form known as martensite. The clay provides a layer of insulation that prevents this rapid cooling, causing it to instead transform into softer, more malleable forms like pearlite: 5. Post-quench. For this, I used canola oil heated to ~100F. Notice that the clay applied above has bubbled up, this is both good and bad. Good because the additional volume and voids provide great insulation, bad because it's extremely fragile and if I accidentally bump it against anything it immediately disintegrates. Luckily, I didn't have anything break off until the actual quench. Personally, I find that this is the hardest part of making a knife: 6. Post-quench, post-temper cleanup. The initial hardened steel is very brittle, so it needs to be softened up a bit so that it doesn't crack under usage. For this knife, I did so by baking it at 410F for about three hours. What you see on the blade now might look like a "hamon" (the demarcation line between the harder martensite and softer steel), but is actually just a difference in oxidation. Which is a little bit of a shame, because it's super dramatic: 7. Initial polishing. You can see a shadow of the actual hamon here: 8. Handle attachment and etch. In order to both provide a little corrosion protection as well as highlight the hamon, the blade was etched with dilute ferric chloride. This oxidizes the surface of the steel and affects the hardened and soft areas in different ways, bringing out the contrast: Super excited to see what you make with it, GEMorris!
|
# ? Dec 19, 2020 01:57 |
|
I have no idea what you'd use that for in woodworking so I'm just gonna imagine it's a tool for a hitman who's tired of a boring old garrote and wants to do something more exciting with necks.
|
# ? Dec 19, 2020 04:30 |
|
Shame Boy posted:I have no idea what you'd use that for in woodworking so I'm just gonna imagine it's a tool for a hitman who's tired of a boring old garrote and wants to do something more exciting with necks. Basically they're good at quickly peeling slices out of a piece of wood. They're good debarking tools. You can also use them for freehand chamfering stock or putting a taper on it, though you'd probably want to use a more precise tool to get to exact dimensions.
|
# ? Dec 19, 2020 04:54 |
|
Shame Boy posted:I have no idea what you'd use that for in woodworking so I'm just gonna imagine it's a tool for a hitman who's tired of a boring old garrote and wants to do something more exciting with necks. Working spindles for chairmaking mostly, but they have other uses as well. You hold the piece in a clamp (preferably a shavehorse) and "draw" the knife toward you, shaping the spindles and tennons.
|
# ? Dec 19, 2020 06:35 |
|
mjan posted:Glad it arrived safe and sound, I had a ton of fun putting it together! Abbreviated build log follows: This is super awesome
|
# ? Dec 19, 2020 15:27 |
|
|
# ? Apr 25, 2024 23:18 |
|
This awesome helping hands with integrated magnifier and telescoping magnet wand arrived last week! Both super practical, useful tools. I've already used the magnet wand twice because I've been soldering boards with through-hole parts, and when I trim the excess bits off of their pins they sometimes like to go flying across the room. Thanks, shrimpwhiskers!
|
# ? Dec 21, 2020 03:21 |