Register a SA Forums Account here!
JOINING THE SA FORUMS WILL REMOVE THIS BIG AD, THE ANNOYING UNDERLINED ADS, AND STUPID INTERSTITIAL ADS!!!

You can: log in, read the tech support FAQ, or request your lost password. This dumb message (and those ads) will appear on every screen until you register! Get rid of this crap by registering your own SA Forums Account and joining roughly 150,000 Goons, for the one-time price of $9.95! We charge money because it costs us $3,400 per month for bandwidth bills alone, and since we don't believe in shoving popup ads to our registered users, we try to make the money back through forum registrations.
  • Post
  • Reply
pmchem
Jan 21, 2010




What model of B&W laser with scanner would you guys favor between these options?

HP Laserjet Pro MFP M148dw https://store.hp.com/us/en/pdp/hp-l...-pro-mfp-m148dw
vs.
Brother HL-L2395DW https://www.brother-usa.com/products/hll2395dw

Adbot
ADBOT LOVES YOU

Thanks Ants
May 21, 2004

Bless You Ants, Blants



Fun Shoe

I'd pick the Brother because trying to navigate different scan option with a two line dot matrix display like the one on the HP is going to be frustrating.

mobby_6kl
Aug 9, 2009

"You are the best poster... do not let anyone say otherwise."


Peachfart posted:

If it is literally feeding the short edge, then it is a very weird issue. But if it is feeding the long edge, I'd bet the drum charge roller is dirty and is causing the yellow line, and the black stuff is likely fuser related, with a possibility of the black drum having an issue. You can be certain if it is the drum or fuser by printing a few solid magenta or cyan prints. If the black ghosting stays the same color it is drum, if it changes to the printed color it is fuser.
Ugh I suppose that was a bit ambiguous, what I meant is that the paper goes in like this, so the short edge and yellow/black lines are parallel with the height (fuuuck or width?) of the drum cylinder:



ShaneMacGowansTeeth posted:

if you can pop the fuser out, just check that the heat rolls inside aren't damaged. If they're okay with no obvious nicks or tears, I'd probably lean towards the drum. The ghosting is probably some residual off-brand toner that's still in the drum, which should go away after a number of prints with proper toner
I think the fuser is fine. Or at least it was fine before I had to force it back in because I didn't realize I had to open the top cover to make it go in normally

I suppose it could be the toner, I'm using aftermarket stuff (made for this model) but there's no way I'm buying OEM toner for a +10y.o. printer that might not even work properly. A $10 ebay drum is the most I can do for it, I think. For this reason, hopefully nobody loses any sleep over this. I just want to figure it out as a matter of principle at this point.


Anyway here's the best look at the fuser roller I could get. It's impossible to tell from the photo bu there are almost no signs of wear


There was this rubbery roller on the flip-out door below the fuser assembly. It was clearly dirty but cleaning it made no difference.


The drum below the fuser assembly (with the yellow warning labels at the top) has clearly visible text on it:


The actual drum was dirty again, but it does wipe off.



Anyway, I then printed a few pages of magenta followed by test pages:
P1: Yellow line, magentish tint to the smearing
P2: Lighter yellow line, black line, more obvious magenta tint
P3: Almost ok, some ghosting form the last page


P6 (new job). P7 (the pube is unrelated)


Honestly this feels like a complete disaster I then printed a page of cyan and the following test pages had clearly cyan stripes on them. So that would point at the fuser then?

Peachfart
Jan 21, 2017


Now I'm not an expert on this particular model of printer, but on any of my machines I'd suspect the itb(internal transfer belt) cleaning unit. If you get ghosting from literally every color it is the most likely option. Your fuser looks perfect and your drums look like crap(especially yellow which is where that line is coming from) but the ghosting is very likely to be the itb cleaning unit. I'm bored so I'm gonna look up your model and then update this post after I find out how your printer cleans the itb.

mobby_6kl
Aug 9, 2009

"You are the best poster... do not let anyone say otherwise."


Thanks, definitely don't waste too much time but if you're bored I suppose it could be a fun way to spend some time I mentioned it before but so you don't have to look for it, it's a CLX-2160, and IIRC the printing guts are compatible with CLP-300. I don't think it has an ITB as such, the toner is dumped form the cartridge and distributed to the roller (that you can see in the 4th photo above) with a few screw gears. There was a problem with the metal plate that scraped excess toner off but I mostly fixed it by scraping off old toner. This roller then seems to directly transfer onto the drum.

Actually looking back at the first sample print, the yellow and black lines were already there, so at least it's not something I messed up with my repair attempts.

ShaneMacGowansTeeth
May 22, 2007



I think this is it... I think this is how it ends


Grimey Drawer

I was today years old when I found out that the phaser 6700 has an interlock switch which cuts power to the laser, which is no big deal. However, this interlock is activated by the rear plastic cover being removed, which absolutely confused the gently caress out of me as I was looking to replace a HVPS and possibly the MCU board and wanted to keep the rear cover off to save some time

Peachfart
Jan 21, 2017


All printers/copiers should have a interlock switch on any covers that lead to major components for the sheer possibility that someone takes a laser in the eye and immediately goes blind. Like, no joke, you'd be blind in that eye permanently. Oh, and the lasers are invisible to regular sight, so fun times.
On my equipment the interlock cuts all power to 24v, leaving only 5v operational.

vaginite
Feb 8, 2006

I'm comin' for you, colonel.

Hey goons what the consensus on a home printer for graphics and materials, like stickers and transfers or whatever, just for hobby use? I can spend up to $500, mainly just looking for highest possible quality and not getting stuck in a corporate ink trap. It's just for hobby stuff too so I don't really need speed or volume and medium format is cool. The only other thing I care about but not really a sticking point is it being easy to load different kinds of paper into for a single print.

SourKraut
Nov 20, 2005

POST QUALITY UNDER CONSTRUCTION




So what are the current views on HP Laserjets? I currently have a HP multi-purpose Officejet that just died on me, and it seems like to get it repaired is going to cost almost as much as the printer cost me itself.

Since my wife and I print and scan somewhat often, but maybe not often enough to keep inkjets from having issues, I have been looking at some of the laser printers with both scan and printing options. Based on reading the thread I had been looking at Brother and Canon, but I saw that Costco just put this HP Laserjet on sale, and so I wasn't sure whether it would be a good buy or if it's still best to avoid HP products.

https://www.costco.com/.product.100652793.html

SlowBloke
Aug 14, 2017


SourKraut posted:

So what are the current views on HP Laserjets? I currently have a HP multi-purpose Officejet that just died on me, and it seems like to get it repaired is going to cost almost as much as the printer cost me itself.

Since my wife and I print and scan somewhat often, but maybe not often enough to keep inkjets from having issues, I have been looking at some of the laser printers with both scan and printing options. Based on reading the thread I had been looking at Brother and Canon, but I saw that Costco just put this HP Laserjet on sale, and so I wasn't sure whether it would be a good buy or if it's still best to avoid HP products.

https://www.costco.com/.product.100652793.html

Seems decent, just be aware that there is a little bit of delay from sending the print to the printer spitting out prints that seems to be a bit slower than average on low end hp laser jet MFP

ShaneMacGowansTeeth
May 22, 2007



I think this is it... I think this is how it ends


Grimey Drawer

In honour of my last day as a field engineer before I embark on a higher paid desk-based role as a co-ordinating supervisor for a big account, I present: Copier In Room With Threatening Shelving Aura



Surprisingly, there was enough room in the hidey hole to detach the professional finisher and allow me to remove the parts - finisher PWB, compiler exit sensor, booklet in sensor and booklet gate solenoid - and not hit either the shelves or the out of shot bucket of stale water

Thanks Ants
May 21, 2004

Bless You Ants, Blants



Fun Shoe

...how many times have those brackets on the left pulled out of the wall

Also I hate Sharp devices, total dogshit

ShaneMacGowansTeeth
May 22, 2007



I think this is it... I think this is how it ends


Grimey Drawer

Thanks Ants posted:

...how many times have those brackets on the left pulled out of the wall

Also I hate Sharp devices, total dogshit

I didn't ask, but the first time I went there I took one look and thought "if I turn around, everything will come falling down" but as I said, there somehow was enough room in there that didn't seem to exist at first glance. And I had nothing to do with the Sharp, just my belligerent Xerox box

Gort
Aug 18, 2003


I have an HP DeskJet 2600 All-in-One printer. I think it cost me about 35. The print quality's okay, but it keeps showing up on my wirelessly-networked Windows machines as offline, then I have to do a bunch of faffing about with its program to reconnect it, which is a bunch of trouble. It also doesn't feed paper correctly. I was doing a fifteen-page print job on crappy quality paper, and it couldn't grab a single sheet without help - I had to physically push the paper into the slot on the top, and occasionally it'd screw up and grab multiple sheets so I'd have to restart the print job.

I want something better... but I don't want to pay 200+ for a Brother printer. I'm mostly just printing RPG crap here (mostly character sheets, but in some cases it's colour paper minis, so quality is nice but not essential).

Is there something that's better than my current HP DeskJet 2600, but won't break the bank? I'd probably be willing to go up to about 100 for a decent, reliable colour printer. I have no use for a scanner or any of the "All-in-One" features, either.

Thanks Ants
May 21, 2004

Bless You Ants, Blants



Fun Shoe

Your budget can get you a decent mono laser printer with low running costs, you're not getting anything colour that isn't poo poo consumer inkjet for that money.

Gort
Aug 18, 2003


Welp, Brother claims another wallet

Oyster
Nov 11, 2005

I GOT FLAT FEET JUST LIKE MY HERO MEGAMAN


Total Clam

ShaneMacGowansTeeth posted:

In honour of my last day as a field engineer before I embark on a higher paid desk-based role as a co-ordinating supervisor for a big account, I present: Copier In Room With Threatening Shelving Aura



Surprisingly, there was enough room in the hidey hole to detach the professional finisher and allow me to remove the parts - finisher PWB, compiler exit sensor, booklet in sensor and booklet gate solenoid - and not hit either the shelves or the out of shot bucket of stale water

As a field engineer contracted to one of those big accounts, congrats.

ShaneMacGowansTeeth
May 22, 2007



I think this is it... I think this is how it ends


Grimey Drawer

Oyster posted:

As a field engineer contracted to one of those big accounts, congrats.

I'm basically being a field engineer and doing other support as well so that two of the sites don't need a field engineer to visit at all as I'll be doing that, and the other two sites which are miles away, the on-site contacts will be going through me before they do anything technical to streamline the process and reduce engineer visits. But all I've done so far is collate the total page counts for each machine, re-do the floor plans for each building on my site, clean out the guy who I'm replacing's stock cupboard - I found a scanner for a machine which had been ordered and replaced by an engineer who'd left the company four years ago on there - sending back two full boxes of spent toner and consumables, making a list of parts I want on site, and just getting everything to a place where I can feel comfortable having every machine working well. Then I'm actually going to start going round and doing monthly maintenance on them all as of next week, just to give myself something to do

Oyster
Nov 11, 2005

I GOT FLAT FEET JUST LIKE MY HERO MEGAMAN


Total Clam

ShaneMacGowansTeeth posted:

I'm basically being a field engineer and doing other support as well so that two of the sites don't need a field engineer to visit at all as I'll be doing that, and the other two sites which are miles away, the on-site contacts will be going through me before they do anything technical to streamline the process and reduce engineer visits. But all I've done so far is collate the total page counts for each machine, re-do the floor plans for each building on my site, clean out the guy who I'm replacing's stock cupboard - I found a scanner for a machine which had been ordered and replaced by an engineer who'd left the company four years ago on there - sending back two full boxes of spent toner and consumables, making a list of parts I want on site, and just getting everything to a place where I can feel comfortable having every machine working well. Then I'm actually going to start going round and doing monthly maintenance on them all as of next week, just to give myself something to do

Ah. That sounds a lot like my present position, I'm technically a TSR(Site) now. I don't get to arrange my machines the way I want to, but have an office in the largest hospital of the account where I keep my parts and my docucare people go through me. I'm jealous of the free time, I've got around 2,500 machines and kept pretty busy.

ShaneMacGowansTeeth
May 22, 2007



I think this is it... I think this is how it ends


Grimey Drawer

Oyster posted:

Ah. That sounds a lot like my present position, I'm technically a TSR(Site) now. I don't get to arrange my machines the way I want to, but have an office in the largest hospital of the account where I keep my parts and my docucare people go through me. I'm jealous of the free time, I've got around 2,500 machines and kept pretty busy.

I have ~90 here and a dozen on another site, and I'm going to encourage the other docucares to come to me first. I've currently got a restricted network machine that shouldn't be where it is that I have to remove the hard-drive, altboot, reconfigure and shuffle back to where it originally was, and a smaller MFP that will actually be the proper restricted machine but I need to arrange all of the back end network stuff plus we have to work out where in this particular building we're going to put it. Naturally, covid is making this difficult

20 Blunts
Jan 21, 2017



im trying to gauge what to buy for small business/contractor's office.

i put out quite a few estimates every week, pay stubs and then send out hundreds of invoices, on top of some internal paperwork we have to do for our trade

we've kind of just been buying a new HP officejet every 1.5 years it seems (they start to die), and they are ink hogs and just kinda suck

is laser worth it at this point?

Adbot
ADBOT LOVES YOU

Thanks Ants
May 21, 2004

Bless You Ants, Blants



Fun Shoe

Mono laser is always worth it, except for colour lasers which you should lease with toners/drums/developer etc. included in a per-page price.

  • 1
  • 2
  • 3
  • 4
  • 5
  • Post
  • Reply