|
Well fatigue got me, I fell asleep midday and woke up to rain so had to run out sand screw the tarp back down. This morning was better so off it came again and it was bone dry in a few hours. Chamfered the edges of the roof boards that were a little thicker than their neighbours  Fitted the extra end timbers and filled the gaps where the roof ended up honestly not perfectly square  Used the 2x6 I cut too short a while ago  Eased the corners so the rubber didn't tear on it  Laid out the rubber to let it relax and unwrinkle  Marked out 100mm from the edges, rolled the rubber back to uncover half the roof, rolled out the water based adhesive up to the 100mm mark  My suspicions that this was just PVA were dashed when my wife pointed out you could smell it at the front of the house, I think my sense of smell pretty much just shut down immediately  Rolled the edges back to see the unglued 100mm  Used the other adhesive for this, on both the roof and the rubber. This one has more interesting hazard signs.  Roll it on, let it flash off then carefully fold it back and brush it smooth. That's how it sits at the moment, going to go out after tea and trim the excess and for the upstands.
|
#
¿
Aug 30, 2020 18:44
|
|
|
|
| # ¿ Apr 26, 2024 06:45 |
|
|
Didn't trim the excess and whatever last night, made pizza and drank beer instead. This morning:  Not the end of the world.  gently caress. Not as bad as it looks, this area is a side with an upstand trim. There's 90+% of this strip adhered so if I tried to pull this back to have another go I'd likely ruin the whole roof. Basically not pretty but for my first go it's acceptable. How did this happen? Almost certainly glue that hasn't finished gassing off, either I didn't leave it long enough or there was excess glue in crevices. This was the scrappiest edge where the slight out of square condition manifested so not 100% surprised.
|
|
#
¿
Aug 31, 2020 09:57
|
|
|
If I were a perfectionist (and I'm obviously not) this step would definitely be "pay a professional" everything under this apart from fitting the door I'd be comfortable saying do it yourself. The end result in the roof is perfectly fine in terms of weather tightness but I'll always be able to see the mistakes and fixes. I'm okay with that, I've always had a problem not starting a project because I know it'll be imperfect, I'd rather finish it imperfect than never get around to starting it.
|
|
#
¿
Aug 31, 2020 14:44
|
|
|
Another week, it rained a lot so I got to see that the gutters I put in are fine. They could be better, the second half had a steeper fall than the first half but they both go the same direction at least. I'll tweak it when it's dry. About the gutter, the drip trim is in two parts, the rectangular profile you screw to the joist header and the y-shaped piece. Instructions are to push the roof rubber into the groove at the top with the top of the y, then clip the y into the groove at the bottom. This is pretty much impossible, I had to go along the roof with a blunted 1/2"brick chisel pushing the rubber into the groove then come along afterwards and clip the y into place. Gutter just sits beneath that.  We tackled the door as all the new hardware turned up, sanding took a couple of hours then my wife gave it a couple of coats of 10 year protective woodstain. It's come up lovely and she's going to give it another couple of coats while I'm at work.  I had to rig up a temporary porch and it ended up naturally curved and we agreed we need something long term so I'll see about making a proper permanent version. Target this week is find a 2450mm sill and install sill and window.
|
|
#
¿
Sep 7, 2020 12:38
|
|
|
Cabin isn't dead, I'm just, struggling. Latest task was to get a window sill for a reasonable price. Nothing used at that size, new everyone wanted £60ish but I found a local building plastics company that would sell me a 6m length for £30. Picked that up in the wife's car, cut it in half in the car park. Trimmed to the right length once home, I need to list the other half for sale and with luck I'll make a bit back if someone wants to collect. That prepared I started to cut a hole in the cabin, starting with the wrap:  Started with the Jigsaw but quickly switched to the router. Battery trim router might not be very ergonomic but it's unbeatable for portability with a flush trim bit.   Stapled and trimmed back  Cut one end of the sill to shape, offer up, mark and cut other end. Generous bead of silicon in the grooves on the underside of the window then screw the sill down to the upside down frame. Place the frame in the opening, clamps just to stop the top moving.  Big rear end screws down into the wooden frame.  Then it's break out the packing shims and square it up and screw it in the sides and top  The light inside is incredible, no regrets.  Packed all the left over 50mm insulation into the roof so it's 150mm now.  Found these low profile dimmable/4000 lumen panels at Costco, after shopping around I'm going back to get two of these next week.  £10 for a sandstone top for the step  Decision still to be made on round Vs square but 3 or 4 of these should make a path.  Spray foamed any gap over 10mm (nozzle width) and caulked anything smaller.  Did the same to the door and window   Went browsing cushion floor/lino. My suggestions were not appreciated.   For real though probably going to get the grey herringbone one at the bottom because that's what my wife would like.  I've been trying to get an electrician in to quote putting in an extra circuit, (house distribution box is full so that's either a small parallel box or a whole new bigger one) running the line to the cabin, installing a 20A distribution unit and 3 double sockets and a double dimmer. I can do a lot of that myself and will if I can save money but it'll all need inspecting and some people don't like inspecting and signing off another person's work. I'll definitely dig the trench though. Unfortunately the guy I used to use a few years ago isn't answering his phone and I've resorted to contacting anyone in the village Facebook group who recently asked about electricians and seeing who they used and if they recommend them. We'll see, don't want to do much else in there until I've had quotes incase I have to pull something down again.
|
|
#
¿
Oct 3, 2020 16:49
|
|
|
Cabin still isn't dead, still struggling. Gave up on any local or local-ish plasterers, some are booked up to 3 years out now. So I'm going to learn how to plaster (I'm under no illusions it's hard as poo poo I know) Caulked the last of the gaps, boarded out with 1/2". I hate drywall screws, I always seem to end up digging bits of swarf out of my fingertips.   In slightly better news it turns out I do have a spare circuit in the consumer unit and I can get the cable from that installed around the outside of the house at a low level where it'll be pretty much unnoticeable, so I'll only need to dig a trench and have the cabin connected/checked/inspected. My next job is actually figuring out the best way/place to put a hole in for the cable, after I spent so much time and effort filling holes  While I was installing this lot I had a little 300w oil filled heater running at about 25% and it kept it lovely and warm.
|
|
#
¿
Dec 14, 2020 13:20
|
|
|
A Small Car posted:Looking good! I would be seriously tempted to just throw up some wallpaper and call it a day, but I don't have a wife to keep happy. I would hate myself forever if I actually did that. The wallpaper, not the wife This may actually happen as my wife wants to put lining paper up and paint that, so screw holes and caulk the joints might happen instead. WiFi is "ok" but after steel cladding I guess it'll step to "dogshit" so I'll be running some donated Cat5 in the trench with whatever shielding is deemed appropriate. (Thanks Tomarse) I'm questions about corner beading strips for plastering, I've seen no mention of using them between the walls and ceiling, only between different walls. Do they just plaster that joint and forget about it?
|
|
#
¿
Dec 18, 2020 11:47
|
|
|
|
| # ¿ Apr 26, 2024 06:45 |
|
|
Oh that makes sense thank you.
|
|
#
¿
Dec 18, 2020 13:01
|
|