|
I just hope 5ghz stays a bit of a niche thing so it doesn't run in to the same problems as 2.4.
|
# ? Dec 21, 2015 07:38 |
|
|
# ? Apr 28, 2024 17:17 |
|
e.pilot posted:I just hope 5ghz stays a bit of a niche thing so it doesn't run in to the same problems as 2.4. I don't know that I'd call it niche, and it's certainly going to be the standard going forward. But even when everybody uses the 5GHz band, it'll still be a vastly superior option due to it's biggest weakness - the smaller range will still reduce interference rather dramatically.
|
# ? Dec 21, 2015 08:11 |
|
Even if everyone starts using 5 GHz it won't be the debacle that 2.4 is currently. Firstly it has 23 20 MHz wide non-overlapping channels - 2.4 has 12 20 MHz wide (in America) channels and only THREE of them are non-overlapping. In tight quarters 5 GHz's relatively poor penetration is a blessing in disguise - even if you and your neighbor are sharing a channel, their signal is likely to be weak enough in your house (and vice versa) that the interference is only a small problem (or maybe not a problem at all) rather everybody being within 10 dB of each other.
|
# ? Dec 21, 2015 08:35 |
|
To add, long range is a double edge sword because of interference. And from skimming this thread just because you can up the power of your antennaes doesn't mind your signal quality will increase in proportion. You introduce more noise which may actually degrade your wifi connection. The safest bet is to create another access point without using bridge mode
|
# ? Dec 21, 2015 09:51 |
|
Great the wireless repeater router for the guest house died. I need a proper solution that's not "shove an old router into the non insulated toolshed part of the guest house" Can't put it in the guest house proper since it's concrete block and can't find the signal from the other router. I guess my only good options are run a line (it's under 200 feet away) or mount some point to point thing right? I'll need to get a switch though since the main router is already out of ports. For a basic non managed switch you just go modem to router --> router port to switch ---> switch to everything that's wired right? Wireless computers connected to the router can see stuff on the switch that way right?
|
# ? Dec 21, 2015 18:24 |
|
havenwaters posted:Great the wireless repeater router for the guest house died. I need a proper solution that's not "shove an old router into the non insulated toolshed part of the guest house" Can't put it in the guest house proper since it's concrete block and can't find the signal from the other router. I guess my only good options are run a line (it's under 200 feet away) or mount some point to point thing right? I'll need to get a switch though since the main router is already out of ports. For the switch question, yeah, as long as your router is bridging the wireless stuff and the wired ports (which is normal) then adding a switch onto one of the LAN ports on the back of the router essentially gives you more LAN ports. For the point to point networking to other building you can either use a pair of wireless bridge devices (Ubiquiti seems to make some decent inexpensive ones) or run a Cat 6 cable. Ethernet cable has a max range of about 100 meters between powered devices so you should be alright within 200 feet and there's outdoor rated cat6. If you have line of sight and easy places to mount the bridge devices I'd probably go with those, but if not then it may be easier to run a cable. Either way you'll want to setup a good access point on the far end of your point to point setup. I'm fond of the Ubiquiti UniFi product line but depending on the size of your guest house it may be overkill.
|
# ? Dec 21, 2015 18:49 |
|
I've run some ridiculous 600ft cat5 runs directly to a client, speed wasn't 100mbit, but it worked surprisingly well until a dump truck ran over it. Such is the ghetto fun of working deployed military communications.
|
# ? Dec 21, 2015 18:56 |
|
e.pilot posted:I've run some ridiculous 600ft cat5 runs directly to a client, speed wasn't 100mbit, but it worked surprisingly well until a dump truck ran over it. I had to fix a slightly too long run that was done by a security company. They added PoE range extenders in the middle of the runs for their cameras but didn't include one for the main LAN connection, so we ended up with a run that worked normally for a little while and then all of the sudden it would get nothing upstream (packet loss and kilobits of data) and yet still managed to speedtest for 30 megabits down. Putting a desktop switch in the middle of the run fixed it until I could order another range extender (luckily it was inside of a building). The run itself wasn't ridiculously long but they broke it up into three sections and I don't think their installers knew anything about ethernet because they're just crimp them straight across with no accounting for the T568A or B standards. I think breaking it up and crimping it incorrectly caused the issues, but the range extender and re-crimping everything sorted it out.
|
# ? Dec 21, 2015 19:35 |
|
havenwaters posted:Great the wireless repeater router for the guest house died. I need a proper solution that's not "shove an old router into the non insulated toolshed part of the guest house" Can't put it in the guest house proper since it's concrete block and can't find the signal from the other router. I guess my only good options are run a line (it's under 200 feet away) or mount some point to point thing right? I'll need to get a switch though since the main router is already out of ports. Yeah that should be fine. I do this at my Dads office, hes got some ancient beast that was out of ports so I just tossed a switch onto one and put other clients onto that.
|
# ? Dec 21, 2015 21:13 |
|
I had a pair of some of the cheapest Ubiquiti devices (Nanostation Loco M5) pointed at each other about 100 or 150 feet away for a point to point. Once I got them set up, I literally never had to touch / log in to them again and they never flaked once. They might well end up cheaper than properly running Cat5E in-ground over that sort of distance, too.
|
# ? Dec 21, 2015 21:35 |
|
Yeah I use a pair of Nanostation Loco M2's to get internet access about 290 feet away from my home router. I don't have direct line of sight so sometimes it drops signal but it's workable for general browsing.
|
# ? Dec 21, 2015 21:37 |
|
I currently have a bunch of Cat 5e ran to various rooms to my first and second floor that terminate in my basement where my router lives. I'm planning on putting an ac access point on each floor and worried about throughput since my servers, office workstations, and the ac access point will be only connects to the basement switch with one gig port. Maybe this is crazy but any ideas on how difficult it would be to run fiber from my second floor (or attic) to my basement? Any ideas that are sane?
|
# ? Dec 22, 2015 00:59 |
|
Are you buying gear that supports 10G? Because 1G on fiber is the same as 1G on copper.
|
# ? Dec 22, 2015 03:39 |
|
Boner Wad posted:I currently have a bunch of Cat 5e ran to various rooms to my first and second floor that terminate in my basement where my router lives. I'm planning on putting an ac access point on each floor and worried about throughput since my servers, office workstations, and the ac access point will be only connects to the basement switch with one gig port. I guess the question is really how much bandwidth you need. I have everything here on gigabit and it's fine for most of what I need with 6 computers, 8 vms and 25 or so mobile devices. At an office I support they have about 15 computers on gigabit and it's also fine, and they have backup software moving files to a nas from each desktop every ten minutes or so. Unless you've got a home based business that moves huge files around constantly gigabit will probably be enough. You have to keep in mind that you internet connection is more likely to be a bottleneck than your LAN.
|
# ? Dec 22, 2015 05:32 |
|
skipdogg posted:Your Atten and SNR levels are solid. You can see the modem is training at 1.528 down/0.133 up which is why you're seeing garbage upload speeds. The link retrains are concerning as are the CRC errors, although a few CRC errors aren't the end of the world. Well the technician never came by but I left him a message asking to be moved to a different port on the DSLAM. I'd posted this in the DSLReports forum as you'd mentioned before finally. One user recommended I call for an 'onshore agent' and ask to have my provisioning reset. I was able to yesterday and now my speed has improved: DownStream Connection Speed 1755 kbps UpStream Connection Speed 284 kbps I only have DSL service and one phone connection that goes straight to my router, no other devices attached to it. The tech checked the box on the side of my house and the line from the phone jack to the router showing no issues. Looks like the provisioning fix did the trick (I hope). I got a reply there, too, saying to try out the Sprint LTE Karma that has an unlimited 5mbps hotspot plan for 50$. My home shows 'good' on their coverage map, however, I don't know what their upload speeds are. Has anyone tried or heard of it before? I think I may switch to it if so since that would be more than double my current speed for nearly the same cost. I've used my t-mobile LTE hotspot for gaming and didn't notice any latency or lag issues. https://yourkarma.com It looks like you get the device, but it's open to any connection. You log in to your account to then use data on it according to your plan. I don't know if my bluray player would work on it then to stream netflix and the like, but it would be nice to get HD 5.1 streaming ability (not sure how to get 5.1 from streaming on my laptop connected by hdmi to my home entertainment system, but the bluray app does so).
|
# ? Dec 22, 2015 12:53 |
|
A couple of quick questions. I'm looking to do some very slight upgrades to my home network (well..really more like one upgrade, the addition of a switch.) Currently, I have a fiber connection that comes into my house as Cat5e (so no modem) that goes directly to my wireless router, a Netgear N900. It comes in the unfinished portion of the basement initially, but there's a cable routed into the finished half of my basement where my router currently stands. The previous owner either had the telecom company do some simple internal wiring, or (more likely) did some himself, based on the fact that it's sort of half-assed (no wall jacks, just cat5e coming/going out of holes in the floor/ceiling.) Right where the telecom's cable ends is where he has two cable drops for the internal wiring. One goes to the living room, and the other goes to a spare bedroom that must have been his office. So currently I have the telecom's cable going to the router, and then the other two cables going out from there. The internal wiring seems to work (haven't tested the one in the other bedroom, just the living room.) However, because it's in the basement, the wifi signal in the rest of the house isn't great, especially the room we actually use as the office (Not the same one he did, so no network drop in that room (yet) and it's nearly as far away as possible from the router and up a floor.) My plan is to get a relatively simple switch (like this TP Link SG108E), put that in the basement, and then put the router in the living room from the existing cable that's routed there. Like so: Two questions: 1) Do I need to get the managed version of that switch? After a mail-in rebate, it's only $5 more than the un-managed, so I figure might as well, right? 2) Assuming I get the managed switch, and I want to assign a static IP to the wired PS4 in the basement, I assume I still assign the IP at the router-level, not the switch, right? clockworkjoe posted:The problem is that it is a pain in the rear end to access. Is there a way to rename the share from \\tplinklogin.net to something easier to type? What are the best android and iOS apps to access the share? Is this the best way to set up a share for streaming video? You can simply make a shortcut on your desktop, have it point to \\tplinklogin.net, name it "Network Share" or whatever and save it. Double-clicking on it will then run it. You could also presumably map it as a network drive. http://www.digitaltrends.com/computing/how-to-map-a-network-drive-windows-7-windows-8-mac-os-x/ I think Win 10 is the same process as Win 8? Not sure about iOS, but in Android, most file explorer apps (like ES File Explorer) can see network drives.
|
# ? Dec 22, 2015 16:11 |
|
DrBouvenstein posted:Two questions: You'll still need a router to act as the middleman between your home network and your ISP, a switch isn't going to cut it. What you can do is get a wired-only router and put that in the basement and then still use your N900 as a wireless access point in the living room. How fast is your internet connection? If it's in the few hundred mbit range the EdgeRouterX is a good choice for a wired router, if you have a gigabit connection then you might want to think about moving up to the EdgeRouter Lite.
|
# ? Dec 22, 2015 16:41 |
|
Krailor posted:You'll still need a router to act as the middleman between your home network and your ISP, a switch isn't going to cut it. poo poo, you're right...don't know why I thought I could get away with just a switch down there. drat, though, $55? Not that I can't afford it, but it's still more than just a $30 switch. And while right now my connection is only 150 Mb/s, I might want to upgrade to their gigabit service in the future, so that's even more money. I'm have tempted to jsut connect the incoming cable from the telecom to the cable going upstairs with a female-to-female coupler, putting the router up there, and then perhaps running a second wire back down the same path for the PS4 to use...though that could be tricky, since I don't have any reliable way to fish that second cable back down (at least not without doing the ol' "tie it to the existing cable and pull' method, which would defeat the purpose since I want that first cable in there, too.) The irony is I work for an IT company that sells and installs networking equipment. You'd think somewhere around here we'd have a fish tape or something, but NOPE! The infrastructure guys don't do cable installs/pulls.
|
# ? Dec 22, 2015 17:25 |
|
DrBouvenstein posted:poo poo, you're right...don't know why I thought I could get away with just a switch down there. You could borrow two boxes of cat 5 and pull two runs through with your existing run as the puller. Also maybe a string in case you need more in the future. Or one run and a string then the other run with the string. If you want some wall mount boxes I've used these monoprice baseboard ones before, they're alright: https://www.monoprice.com/product?p_id=7090 I don't think they come with the punchdown tool, though.
|
# ? Dec 22, 2015 17:35 |
|
DrBouvenstein posted:drat, though, $55? Not that I can't afford it, but it's still more than just a $30 switch. You work for a place that sells network equipment to businesses and you're balking at a $55 router?
|
# ? Dec 22, 2015 17:56 |
|
Inspector_666 posted:You work for a place that sells network equipment to businesses and you're balking at a $55 router? My home needs are far, FAR below that of even a small business. I think I'll do the 'use existing cable to pull two' method. I'm just worried about the extra width of three total cables...even if I offset it so the plugs are spaced far enough apart, it still might snag somewhere. To be safe, I think I'll use the existing one to pull a string, then use the string to pull the new ones. DrBouvenstein fucked around with this message at 18:12 on Dec 22, 2015 |
# ? Dec 22, 2015 18:08 |
|
Good thing the Edgerouter X isn't really appropriate for most businesses, but well suited for SOHO/home installs.
|
# ? Dec 22, 2015 18:12 |
|
DrBouvenstein posted:My home needs are far, FAR below that of even a small business. Ok but $55 for a router is cheap regardless...
|
# ? Dec 22, 2015 18:13 |
|
Inspector_666 posted:Ok but $55 for a router is cheap regardless... I wasn't trying to compare that cost to that of a business router, just making the point that it's silly to compare the cost of routers my company sells to one for home use. And what's wrong with not wanting to spend more money if I don't have to? Obviously, there comes a point where the money saved isn't worth the time and effort, but I don't think I'm there, yet.
|
# ? Dec 22, 2015 18:17 |
|
Depending on how cheap you want to be, you can run monowall or something on an old PC with multiple NICs. The power bill will eventually outweigh the cost of a new device but it will take a while. If you already have an AP (and you do, counting the N900) then any old router will probably be fine for just handling the NAT connections over wired. You don't necessarily need to get the $55 model.
|
# ? Dec 22, 2015 19:22 |
|
What's generally the easiest way of making a Windows files system accessible from outside the house? I'm going to be away for a few months, so providing my fileserver stays up I'd like to be able to jump in and grab stuff as needed. I have VNC Server running on it so I can use the interface at least, but moving files back/forth obviously not supported. I have VPN elements on my router (an ASUS N66u) but when I tried the before I could use the internet connection at my house OK (i.e. 'whats my IP' websites would return the line where the box sits), but I couldn't see any of the machines on the network. Not sure if the updated and 3rd party Merlin firmware I use changes that at all but could be worth another shot if that's generally regarded as a way to do this?
|
# ? Dec 22, 2015 20:59 |
|
Depending on how many files you need to transfer, something like Teamviewer might work for you. It's pretty good at getting through NAT, and has VNC and file transfer capabilities. edit: Free for personal use.
|
# ? Dec 22, 2015 23:20 |
|
spoof posted:Depending on how many files you need to transfer, something like Teamviewer might work for you. It's pretty good at getting through NAT, and has VNC and file transfer capabilities. Yeah, if you want to be able to pull files off of the remote computer, Teamviewer will make it easy. If you want to be able to mount the FS as a network drive or stream media, then you need to get the VPN set up or install Plex or something (for streaming media, that is.)
|
# ? Dec 22, 2015 23:38 |
|
I've never tried teamviewer before, I'll bung an install on while I'm away for a few days and see how it is. What's the disadvantages to using it over a mountable system? I honestly thought it was more of a VNC client, so I'll do some reading up. Yeah, this is my plex server I'm talking about so that part should be golden. It's a shame my main playback client is the older Apple TV, as I'll lose plex ability as it relies on PlexConnect which has to be run local. I could run that on my laptop I suppose, just means relying on that always being up. Probably worth the 30 minutes to get it up and running though. Cheers!
|
# ? Dec 23, 2015 01:14 |
|
With Teamviewer you're actually copying the files to/from the remote computer. Using a VPN you could just attach to the remote file storage and view it on the local machine without having to wait for the entire thing to copy.
|
# ? Dec 23, 2015 01:19 |
|
Ah fair, that should be fine as if I'm transferring any video it's because it'll end up on a USB stick to put on a cheap and cheerful media player anyway so in theory shouldn't be an issue. Sounds like a winner, thanks!
|
# ? Dec 23, 2015 01:35 |
|
I'm running OpenVPN on my N66U with Merlin's firmware and haven't had any issues. Make sure you're using DDNS and you should be golden; all of the devices in our home are set up to use it and we can access our NAS just as easily as if we were in the house. The extra security when using a public hotspot is also a bonus.
|
# ? Dec 23, 2015 01:51 |
|
I have a domain binded to the router for other services so sounds worth giving another shot. Did you leave everything on pretty much defaults? If you have a screenshot of how its setup for you (minus anything personal of course), that would be appreciated. I could probably get benefits from running both that and TV side by side.
|
# ? Dec 23, 2015 02:07 |
|
Sure thing. I'm out and about right now so I'm just on my phone, but I'll post what I can when I get home.
|
# ? Dec 23, 2015 02:09 |
|
Rexxed posted:I guess the question is really how much bandwidth you need. I have everything here on gigabit and it's fine for most of what I need with 6 computers, 8 vms and 25 or so mobile devices. At an office I support they have about 15 computers on gigabit and it's also fine, and they have backup software moving files to a nas from each desktop every ten minutes or so. Unless you've got a home based business that moves huge files around constantly gigabit will probably be enough. You have to keep in mind that you internet connection is more likely to be a bottleneck than your LAN. Yeah after I posted that I realized 10G is insane. I'm thinking that I'm going to have to run new drops to rooms from my attic and then figure out how to get a link from the attic switch into my basement. I guess I could take an existing run to an outlet that terminates in the basement and extend it up to the attic and then run a new cable down for the existing outlet which would give me the uplink I need. How else do you get from the attic to the basement without ripping walls out? Also the cable installers stapled the Ethernet during the house construction so I can't pull a bundle through.
|
# ? Dec 23, 2015 03:02 |
|
I am running a traceroute from my laptop to another device on my network. The connection flow is Laptop -> (Wi-Fi) -> Time Capsule -> (Ethernet) -> Router -> Ethernet -> Other device However, when I do a traceroute, there is one hop, directly to the other device. I would have expected at least the router to show up. Why doesn't it?
|
# ? Dec 23, 2015 03:06 |
|
Boner Wad posted:Yeah after I posted that I realized 10G is insane. If you have a vent stack running from the basement to the attic you could run parallel to that, though they're usually completely sealed all the way around on each floor, so you'd have to drill a hole on each level. Not sure what your local code would be for running low-voltage wiring (and if you need plenum-rated) beside it, though. You could also find a corner of the house that each floor shares and drill outside the wall and just cover up the cable with a raceway. Most can be painted and cover up really well (I ended up doing this).
|
# ? Dec 23, 2015 03:32 |
|
Axiem posted:I am running a traceroute from my laptop to another device on my network. Most of the time people have wifi broadcasting from their router. The other devices on the network are attached to the router as well, but you don't route through them to get to the internet. Do you have a nonstandard setup?
|
# ? Dec 23, 2015 03:47 |
|
Rexxed posted:Most of the time people have wifi broadcasting from their router. The other devices on the network are attached to the router as well, but you don't route through them to get to the internet. Do you have a nonstandard setup? My Wi-Fi is broadcasting from an Apple Time Capsule, but it's just in Bridge mode; the router is an EdgeRouter X set up with the WAN2LAN2 wizard plus tweaking the name servers.
|
# ? Dec 23, 2015 03:51 |
|
|
# ? Apr 28, 2024 17:17 |
|
Axiem posted:My Wi-Fi is broadcasting from an Apple Time Capsule, but it's just in Bridge mode; the router is an EdgeRouter X set up with the WAN2LAN2 wizard plus tweaking the name servers. It's possible your traceroute software is ignoring local subnet hops but if it's not that then I'm not really sure.
|
# ? Dec 23, 2015 04:01 |